Page History

Wiki Markup{{The setjmp()}} should only be invoked from one of the contexts listed in §7 macro should be invoked from only one of the contexts listed in subclause 7.13.1.1 of \[of the C Standard [ISO/IEC 9899:1999|AA. References#ISO/IEC 9899-1999]\]. Invoking {{2011]. Invoking setjmp()}} outside of one of these contexts results in undefined behavior (see [Undefined Behavior 119|CC. Undefined Behavior#ub_119]).. (See undefined behavior 125.)

After invoking longjmp(), non-volatile-qualified local objects should not be accessed if their values could have changed since the invocation of setjmp(). Their value in this case is considered indeterminate, and accessing them is undefined behavior (see Undefined Behavior 121, 10).. (See undefined behaviors 127 and 10.)

The longjmp() function should never be used to return control to a function that has terminated execution (see Undefined Behavior 120). (See undefined behavior 126.)

Signal masks, floating-point status flags, and the state of open files are not saved by the setjmp() function. If signal masks need to be saved, the POSIX sigsetjmp() function should be used.

This recommendation is related to SIG32SIG30-C. Do not call longjmp() from inside a signal handler and Call only asynchronous-safe functions within signal handlers and ENV32-C. All atexit exit handlers must return normally.

Noncompliant Code Example

The following This noncompliant code example calls setjmp() in an assignment statement, resulting in undefined behavior.:

jmp_buf buf;

void f(void) {
  int i = setjmp(buf);
  if (i == 0) {
    g();
  } else {
    /* longjmp was invoked */
  }
}

void g(void) {
  /* ... */
  longjmp(buf, 1);
}

...

Placing the call to setjmp() in the if statement and (, optionally) , comparing it with a constant integer removes the undefined behavior., as shown in this compliant solution:

jmp_buf buf;

void f(void) {
  if (setjmp(buf) == 0) {
    g();
  } else {
    /* longjmp was invoked */
  }
}

void g(void) {
  /* ... */
  longjmp(buf, 1);
}

Noncompliant Code Example

Any attempt to invoke the longjmp() function to transfer control to a function that has terminated completed execution results in undefined behavior. :

#include <setjmp.h>
#include <stdio.h>
#include <stdlib.h>

static jmp_buf buf;
static void bad(void);

static void g(void f() {
  if (setjmp(buf) == 0) {
   g printf("setjmp() invoked\n");
  } else {
  h  printf("longjmp() invoked\n");
  return;}
}

static void gf(void) {
  if (setjmp(buf) != 0g();
}

static void setup(void) {
  f();
}

void do_stuff(void) {
  void (*b)(void) = bad;
  /* longjmp was invoked... */
  longjmp(buf, 1);
}

static void bad(void) {
  printf("Should not be called!\n");
  returnexit(1);
}

voidint hmain(void) {
  setup();
 /* ... */
  longjmp(buf, 1);
}

Compliant Solution

 do_stuff();
}

Implementation Details

Compiled at -O0 using GCC 7.5 or Clang 8.0 on Ubuntu 18.04 (Linux for x86-64), the preceding example outputs the following when run:

setjmp() invoked
longjmp() invoked
Should not be called!

Because g() has finished executing at the time longjmp() is called, it is no longer on the stack. When do_stuff() is invoked, its stack frame occupies the same memory as the old stack frame of g(). In this case, a was located in the same location as the return address of function g(). The assignment of b overwrites the return address, so when longjmp() sends control back to function g(), the function returns to the wrong address (in this case, to function bad()).

If the array b were user specified, the user would be able to set the return address of function g() to any location.

Compliant Solution

The longjmp() function should be used only when longjmp() should only be used when the function containing the corresponding setjmp() is guaranteed not to have terminated completed execution, as in the following example.:

#include <setjmp.h>
#include <stdio.h>
#include <stdlib.h>

static jmp_buf buf;
static void bad(void);

void fdo_stuff(void) {
  ifvoid (setjmp*b)(bufvoid) != 0) {
  bad;
  /* longjmp was invoked ... */
  longjmp(buf, 1);
} else

static void bad(void) {
  printf("Should  h(not be called!\n");
  }
  returnexit(1);
}

int main(void h() {
  /* ... */
  longjmp(buf, 1);
}

Noncompliant Code Example

) {
  if (setjmp(buf) == 0) {
    printf("setjmp() invoked\n");
  } else {
    printf("longjmp() invoked\n");
  }
  do_stuff();
} 

There is no risk of overwriting a return address because the stack frame of main() (the function that invoked setjmp()) is still on the stack; so when do_stuff() is invoked, the two stack frames will not overlap.

Noncompliant Code Example

In this noncompliant example, nonNon-volatile-qualified objects local to the function that invoked the corresponding setjmp() have indeterminate values after longjmp() has been is executed if their value has been changed since the invocation of setjmp().:

jmp_buf buf;

void f(void) {
  int i = 0;
  if (setjmp(buf) != 0) {
    printf("%i\n", i);
    /* ... */
  }
  i = 2;
  g();
}

void g(void) {
  /* ... */
  longjmp(buf, 1);
}

Implementation Details

Calling f() will print 2 if you compile with -O0, but will print 0 if you compile with -O2.  This involves using GCC 7.5 or Clang 8.0 on Ubuntu 18.04 (Linux x86-64).

Compliant Solution

If an object local to the function that invoked setjmp() needs to be accessed after longjmp() returns control to the function, the object should be volatile-qualified.:

jmp_buf buf;

void f(void) {
  volatile int i = 0;
  if (setjmp(buf) != 0) {
    printf("%i\n", i);
    /* ... */
  }
  i = 2;
  g();
}

void g(void) {
  /* ... */
  longjmp(buf, 1);
}

This will now correctly print 2 regardless of optimization level.

Risk Assessment

References

Automated Detection

...

Image Added Image Added Image Added Wiki Markup\[[ISO/IEC 9899:1999|AA. References#ISO/IEC 9899-1999]\] Section 7.13, "Nonlocal jumps <setjmp.h>", Section J.2, "Portability issues"