Page History

Wiki MarkupIf a {{while}} or {{for}} statement uses a loop counter, and increments or decrements it by more than one, it should use a numerical comparison operator (that is, <, <=, >, or >=) to terminate the loop. This prevents the loop from executing indefinitely or until the counter wraps around and reaches the final value (\[[INT00-J. Perform explicit range checking to ensure integer operations do not overflow]\])Unless coded properly, a while or for loop may execute forever or until the counter wraps around and reaches its final value. (See NUM00-J. Detect or prevent integer overflow.) This problem may result from incrementing or decrementing a loop counter by more than one and then testing for equality to a specified value to terminate the loop. In this case, it is possible that the loop counter will leapfrog the specified value and execute either forever or until the counter wraps around and reaches its final value. This problem may also be caused by naïve testing against limits—for example, looping while a counter is less than or equal to Integer.MAX_VALUE or greater than or equal to Integer.MIN_VALUE.

Noncompliant Code Example

This noncompliant code example appears to iterate five times:

for (i = 1; i != 10; i += 2) {
  // ...
}

However, the loop never terminates because the successive . Successive values of i are 1, 3, 5, 7, 9 and , 11, allowing and so on; the comparison with 10 never evaluates to be skipped. On a Java based system, the true. The value reaches the maximum representable positive number (Integer.MAX_VALUE) and on subsequent incrementing, then wraps to the second-lowest negative number (Integer.MIN_VALUE + 1). It then works its way up to -1–1, then 1, and proceeds as described earlier.

Noncompliant Code Example

This noncompliant code example terminates but performs more iterations than expected:

for (i = 1; i != 10; i += 25) {
  // ...
}

Noncompliant Code Example

This noncompliant code example terminates, but takes more iterations than expected. It increments i so that it is Successive values of i are 1, 6, and 11, skipping past 10. The value of i then wraps from near the maximum positive value to near the lowest negative value and works its way up toward zero0. It then assumes 2, 7, and 12, skipping past 10 again. After the value wraps from the high-positive to the low-negative side three more times, it finally reaches 0, 5, and 10, terminating the loop.

Compliant Solution

One solution is to simply ensure the loop termination condition is reached before the counter inadvertently wraps.

for (i = 1; i !== 1011; i += 52) {
  // ...
}

Compliant Solution

Using This solution can be fragile when one or more of the conditions affecting the iteration must be changed. A better solution is to use a numerical comparison operator guarantees proper loop termination(that is, <, <=, >, or >=) to terminate the loop.

for (i = 1; i <= 10; i += 2) {
  // ...
}

This latter solution can be more robust in the event of changes to the iteration conditions. However, this approach should never replace careful consideration regarding the intended and actual number of iterations.

Noncompliant Code Example

Numerical comparison operators do not ensure loop termination when comparing with A loop expression that tests whether a counter is less than or equal to Integer.MAX_VALUE or greater than or equal to Integer.MIN_VALUE will never terminate because the expression will always evaluate to true. For example, the following loop will never terminate because i can never be greater than Integer.MAX_VALUE:

for (i = 1; i <= Integer.MAX_VALUE; i ++= 2) {
  // ...
}

Compliant Solution

It is not sufficient to compare with The loop in this compliant solution terminates when i is equal to Integer.MAX_VALUE - 1 when the loop counter is more than 1. To be safe, ensure that the comparison is carried out with (:

for (i = 1; i != Integer.MAX_VALUE; i++) {
  // ...
}

If the loop is meant to iterate for every value of i greater than 0, including Integer.MAX_VALUE, it can be implemented as follows:

i = 0;
do {
  i++
  // ...
} while (i != Integer.MAX_VALUE);

Noncompliant Code Example

This noncompliant code example initializes the loop counter i to 0 and then increments it by 2 on each iteration, basically enumerating all the even, positive values. The loop is expected to terminate when i is greater than Integer.MAX_VALUE - 1, an even value. In this case, the loop fails to terminate because the counter wraps around before becoming greater than Integer.MAX_VALUE - 1.

for (i = 0; i <= Integer.MAX_VALUE - 1; i += 2) {
  // ...
}

Compliant Solution

The loop in this compliant solution terminates when the counter i is greater than Integer.MAX_VALUE minus the step value as the loop-terminating condition counter's value).

for (i = 10; i <= Integer.MAX_VALUE - 2; i += 2) {
  // ...
}

Risk Assessment

Applicability

Incorrect termination of loops Testing for exact values to terminate a loop may result in infinite loops, poor performance, incorrect results, and other problems. In any of the conditions used to terminate a loop can be influenced by an attacker, these errors can be exploited to cause a denial of service or other attack.

...

Automated Detection

Automated Detection

None.

Related Vulnerabilities

Search for vulnerabilities resulting from the violation of this rule on the CERT website.

Other Languages

This rule appears in the C Secure Coding Standard as MSC21-C. Use inequality to terminate a loop whose counter changes by more than one .

This rule appears in the C++ Secure Coding Standard as MSC21-CPP. Use inequality to terminate a loop whose counter changes by more than one.

References

Bibliography

...

Image Added Image Added Image Added Wiki Markup\[[JLS 05|AA. Java References#JLS 05]\] 15.20.1 Numerical Comparison Operators <, <=, >, and >=